Woolich Racing Products are Intended for RACE USE on CLOSED CIRCUIT ONLY User Guides and Installation InstructionsĮlectronic Mapping - Plug and Play Performance
Note: The Hacker/Tweaker is a bare PCB board, you will need to make your own case. It powers up right from the Zt-3 DATA port. There are two mounting holes for screws or standoffs. Like all LED displays it requires a tinted foil or Lexan cover.
#YAMAHA R6 ECU FLASH FULL#
Designed to fit into tight spots, full board dimensions are less than 2" by 1". The Zeitronix Hacker/Tweaker is a very small AFR or Lambda display for the Zt-3 Wideband Systems.
Red digital AFR readout with large 0.4" (10mm) digits.High contrast display visible even in direct sunlight.Blue digital AFR readout with large 0.4" (10mm) digits.Programmable to startup as an AFR or Lambda gauge.Slim design for flexible gauge mounting options.Stylish, machined, anodized black bezel and slim enclosure.The Narrowband to Wideband O2 sensor adapter screws into a 12mm Narrowband bung, allowing you to use a Wideband O2 sensor with a Narrowband bung. The Stainless Steel 12mm Narrowband Bung Bolt allows you to block off a Narrowband O2 bung allowing the Narrowband sensor to be entirely removed from the bike. This Race version of the bung bolt is light weight and has holes pre-drilled for lock wiring. The Stainless Steel Wideband Bung Bolt allows you to block off a Wideband O2 bung when the Wideband O2 sensor is not installed. You can weld this bung into exhaust systems that do not have a Wideband O2 bung. High Quality 18mm Titanium Wideband O2 Bung. High Quality 18mm Stainless Steel Wideband O2 Bung. Zeitronix ZT-3 Wideband O2 Installation Guide Woolich Racing embroidered keytag - easy to retrieve your keys even with bike gloves on! Woolich Racing AutoTune Live - Dyno Use Only - (Requires Applicable LogBox + Zeitronix Package)Īdjustable embroidered Woolich Racing hat.Race Shift Pattern Sensor Configuration - (Requires Race Tools).Pit Lane Limiter - (Requires Race Tools).Electronic Throttle Valve Deceleration Maps.
#YAMAHA R6 ECU FLASH SOFTWARE#
Purchase this item to gain access in the Woolich Racing Tuned software to the stock bin files for the 2008-2011 Yamaha YZF-R6.įeatures available for Yamaha YZF-R6 2008-2011
#YAMAHA R6 ECU FLASH INSTALL#
If you do not have a Woolich Racing Interface you can also visit a Woolich Racing - Tuning Partner and have them install and configure the Race Tools (additional fees and charges will apply).Ģ008-2011 Yamaha YZF-R6 Launch Control Keyīin File Definitions - for use in Woolich Racing Tuned softwareĢ008-2011 Yamaha YZF-R6 Stock Bin File Definitions You can purchase this as a package on the product page for your bike. You will need to use the relevant Woolich Racing Interface and Bin File Definition to enable and configure Race Tools and write to the ECU. Woolich Racing Race Tools requires you to Write the ECU. *** The Pit Speed Limiter / Engine Warm Up requires the purchase of an additional Pit Speed Limiter harness ** This harness uses the stock exhaust valve plugs on the bike's harness, the stock exhaust valve should be removed from the bike and disabled in the WRT software * Contact us after ordering if you have after-market rearsets or are using a race shift pattern and we will swap the shift rod for a generic rod that can be cut and tapped to the correct length. Pit Speed Limiter RPM can be configured.***Įngine Warm Up parameters are configurable.*** Launch Control allows you to configure Delay, Launch RPM and Hold Speed. Quickshifter Kill times are configurable per gear with 3D maps allowing Kill Times to be set for the full range of TPS and RPM combinations.Īutoblipper Opening and Duration maps are fully configurable per gear.